Chưa cập nhật
品番: 131150435
- 単位
- Chưa cập nhật
コンテンツを読み込み中…
コンテンツを読み込み中…
オンライン決済は不要です。TESFA が品番、数量、供給条件を確認し、ご入力の連絡先へ見積を回答します。
MRO 品では、画像だけで選ぶより正しいコード確認が重要です。TESFA は見積確定前に主要な技術項目を確認します。
Khóa liên động điện từ Schmersal 101178664.
品番
101178664
単位
Chưa cập nhật
供給状況
見積はお問い合わせください
必要数量 (Chưa cập nhật)
オンライン決済は不要です。TESFA が品番、数量、供給条件を確認し、ご入力の連絡先へ見積を回答します。
MRO 品では、画像だけで選ぶより正しいコード確認が重要です。TESFA は見積確定前に主要な技術項目を確認します。
| 属性 | 製品仕様 |
|---|---|
| Mã sản phẩm | 101178664 |
| Mã đặt hàng Schmersal | 101178664 |
| Model Schmersal | AZM 200SK-T-1P2P |
| Working principle | inductive |
| Housing material | Glass-fibre, reinforced thermoplastic |
| Reaction time, maximum | 60 ms |
| Duration of risk, maximum | 120 ms |
| Gross weight | 570 g |
| Power to unlock | Yes |
| Solenoid interlock monitored | Yes |
| Manual release | Yes |
| Short circuit detection | Yes |
| Cross-circuit detection | Yes |
| Series-wiring | Yes |
| Safety functions | Yes |
| Integral system diagnostics, status | Yes |
| Number of safety contacts | 2 |
| Performance Level, up to | e | d |
| Category | 4 | 2 |
| PFH value | 4.00 x 10−9 /h | 2.50 x 10−9 /h |
| PFD value | 1.00 x 10−4 | 2.20 x 10−4 |
| Safety Integrity Level (SIL), suitable for applications in | 3 | 2 |
| Holding force FZh in accordance with EN ISO 14119 | 2,000 N |
| Note (holding force FZh) | 1,000 N when used with the AZ/AZM201-B30 actuator, for indoor use. |
| Holding force Fmax, maximum | 2,600 N |
| Note (holding force Fmax) | 1,300 N when used with the AZ/AZM201-B30 actuator, for indoor use. |
| Latching force | 30 N |
| Actuating speed, maximum | 0.2 m/s |
| Tightening torque of the fastening screws for the housing cover, minimum | 0.7 Nm |
| Tightening torque of the fastening screws for the housing cover, maximum | 1 Nm |
| Note | Torx T10 | All indications including the conductor ferrules. |
| Termination | Screw terminals M20 x 1.5 |
| Cable section, minimum | 0.25 mm2 |
| Cable section, maximum | 1.5 mm2 |
| Wire cross-section, minimum | 23 AWG |
| Wire cross-section, maximum | 15 AWG |
| Allowed type of cable | flexible solid multi-wire solid single-wire |
| Length of sensor | 50 mm |
| Width of sensor | 40 mm |
| Height of sensor | 220 mm |
| IP Degree of protection | IP67 |
| Ambient temperature | -25 ... +60 °C |
| Storage and transport temperature | -25 ... +85 °C |
| Relative humidity, minimum | 30 % |
| Relative humidity, maximum | 95 % |
| Note (Relative humidity) | non-condensing |
| Resistance to vibrations | 10 ... 55 Hz, amplitude 1 mm |
| Restistance to shock | 30 g / 11 ms |
| Protection class | II |
| Rated insulation voltage Ui | 32 VDC |
| Rated impulse withstand voltage Uimp | 0.8 kV |
| Overvoltage category | III |
| Degree of pollution | 3 |
| Operating voltage | 24 VDC -15 % / +10 % |
| No-load supply current I0, typical | 600 mA |
| Rated operating voltage | 24 VDC |
| Operating current | 50 mA |
| Time to readiness, maximum | 4,000 ms |
| Switching frequency, approx. | 1 Hz |
| Switching thresholds | -3 V ... 5 V (Low) 15 V ... 30 V (High) | −3 V ... 5 V (Low) 15 V ... 30 V (High) |
| Magnet switch-on time | 100 % |
| Current consumption at 24 V | 5 mA |
| Rated operating current (safety outputs) | 250 mA |
| Voltage drop Ud, maximum | 4 V | 4 V |
| Leakage current Ir, maximum | 0.5 mA |
| Voltage, Utilisation category DC-13 | 24 VDC | 24 VDC |
| Current, Utilisation category DC-13 | 0.25 A | 0.05 A |
| Note (LED switching conditions display) | Error / functional defect: LED red Operating condition: LED green Supply voltage UB: LED green |
| Recommendation (actuator) | AZ/AZM 200-B1 |
| Note (General) | As long as the actuating unit remains inserted in the solenoid interlock, the unlocked safety guard can be relocked. In this case, the safety outputs are re-enabled, so that the safety guard must not be opened. |
品番: 131150435
品番: 151180590
品番: 103040784
品番: 101133843
Hướng dẫn đọc mã van điện từ SMC dòng SY3000, SY5000, SY7000 và SY9000 theo catalog hãng, kèm ví dụ SKU thật và checklist tránh đặt nhầm cấu hình.
Theo đường đi của khí nén để hiểu tiền điện đến từ đâu, tính thử chi phí và chuẩn bị checklist kiểm tra rò rỉ trong nhà máy.
Chọn ống khí PU/PA theo kích thước, áp suất tại nhiệt độ dùng, bán kính uốn và môi trường. Có bảng đối chiếu và checklist thay ống MRO.
