Chưa cập nhật
品番: 131150435
- 単位
- Chưa cập nhật
コンテンツを読み込み中…
コンテンツを読み込み中…
オンライン決済は不要です。TESFA が品番、数量、供給条件を確認し、ご入力の連絡先へ見積を回答します。
MRO 品では、画像だけで選ぶより正しいコード確認が重要です。TESFA は見積確定前に主要な技術項目を確認します。
Khóa liên động điện từ Schmersal 103013909.
品番
103013909
単位
Chưa cập nhật
供給状況
見積はお問い合わせください
必要数量 (Chưa cập nhật)
オンライン決済は不要です。TESFA が品番、数量、供給条件を確認し、ご入力の連絡先へ見積を回答します。
MRO 品では、画像だけで選ぶより正しいコード確認が重要です。TESFA は見積確定前に主要な技術項目を確認します。
| 属性 | 製品仕様 |
|---|---|
| Mã sản phẩm | 103013909 |
| Mã đặt hàng Schmersal | 103013909 |
| Model Schmersal | AZM201Z-ST2-T-1P2PW |
| Coding | Universal coding |
| Coding level according to EN ISO 14119 | Low |
| Working principle | RFID |
| Frequency band RFID | 125 kHz |
| Transmitter output RFID, maximum | -6 dBm |
| Housing material | Glass-fibre, reinforced thermoplastic |
| Duration of risk, maximum | 200 ms |
| Reaction time, switching off safety outputs via actuator, maximum | 100 ms |
| Reaction time, switching off safety outputs via safety inputs, maximum | 1.5 ms |
| Gross weight | 495 g |
| Power to unlock | Yes |
| Solenoid interlock monitored | Yes |
| Manual release | Yes |
| Short circuit detection | Yes |
| Cross-circuit detection | Yes |
| Series-wiring | Yes |
| Safety functions | Yes |
| Integral system diagnostics, status | Yes |
| Number of digital fail-safe inputs | 2 |
| Number of fail-safe digital outputs | 2 |
| Performance Level, up to | e | d |
| Category | 4 | 2 |
| PFH value | 1.90 x 10−9 /h | 1.00 x 10−8 /h |
| PFD value | 1.60 x 10−4 | 8.90 x 10−4 |
| Safety Integrity Level (SIL), suitable for applications in | 3 | 2 |
| Holding force FZh in accordance with EN ISO 14119 | 2,000 N |
| Note (holding force FZh) | 1,000 N when used with the AZ/AZM201-B30 actuator, for indoor use. |
| Holding force Fmax, maximum | 2,600 N |
| Note (holding force Fmax) | 1,300 N when used with the AZ/AZM201-B30 actuator, for indoor use. |
| Latching force | 30 N |
| Actuating speed, maximum | 0.2 m/s |
| Type of the fixing screws | 2x M6 |
| Tightening torque of the fixing screws, maximum | 8 Nm |
| Tightening torque of the fastening screws for the housing cover, minimum | 0.7 Nm |
| Tightening torque of the fastening screws for the housing cover, maximum | 1 Nm |
| Note | Torx T10 |
| Length of sensor chain, maximum | 200 m |
| Note (length of the sensor chain) | Cable length and cross-section change the voltage drop dependiing on the output current |
| Note (series-wiring) | Unlimited number of devices, oberserve external line fusing, max. 31 devices in case of serial diagnostic SD |
| Termination | Connector M12, 8-pole |
| Length of sensor | 50 mm |
| Width of sensor | 40 mm |
| Height of sensor | 220 mm |
| IP Degree of protection | IP66 IP67 |
| Ambient temperature | -30 ... +60 °C |
| Storage and transport temperature | -30 ... +85 °C |
| Relative humidity, maximum | 93 % |
| Note (Relative humidity) | non-condensing non-icing |
| Resistance to vibrations | 10 ... 150 Hz, amplitude 0.35 mm |
| Restistance to shock | 30 g / 11 ms |
| Protection class | III |
| Permissible installation altitude above sea level, maximum | 2,000 m |
| Rated insulation voltage Ui | 32 VDC |
| Rated impulse withstand voltage Uimp | 0.8 kV |
| Overvoltage category | III |
| Degree of pollution | 3 |
| Operating voltage | 24 VDC -15 % / +10 % (stabilised PELV power supply) |
| No-load supply current I0, typical | 50 mA |
| Current consumption with magnet ON, average | 200 mA |
| Current consumption with magnet ON, peak | 700 mA / 100 ms |
| Rated operating voltage | 24 VDC |
| Operating current | 1,200 mA | 50 mA |
| Required rated short-circuit current | 100 A |
| External wire and device fuse rating | 2 A gG |
| Time to readiness, maximum | 4,000 ms |
| Switching frequency, maximum | 1 Hz |
| Designation, Magnet control | IN |
| Switching thresholds | -3 V ... 5 V (Low) 15 V ... 30 V (High) | −3 V ... 5 V (Low) 15 V ... 30 V (High) |
| Current consumption at 24 V | 10 mA | 5 mA |
| Magnet switch-on time | 100 % |
| Test pulse duration, maximum | 5 ms | 1 ms | 0.5 ms |
| Test pulse interval, minimum | 40 ms | 100 ms |
| Classification ZVEI CB24I, Sink | C0 | C1 | C1 C2 |
| Classification ZVEI CB24I, Source | C1 C2 C3 | C1 C2 C3 | C2 |
| Designation, Safety inputs | X1 and X2 |
| Designation, Safety outputs | Y1 and Y2 |
| Rated operating current (safety outputs) | 250 mA |
| Design of control elements | short-circuit proof, p-type | short-circuit proof, p-type |
| Voltage drop Ud, maximum | 2 V | 4 V |
| Leakage current Ir, maximum | 0.5 mA |
| Voltage, Utilisation category DC-13 | 24 VDC | 24 VDC |
| Current, Utilisation category DC-13 | 0.25 A | 0.05 A |
| Test pulse interval, typical | 1,000 ms |
| Designation, Diagnostic outputs | OUT |
| Note (LED switching conditions display) | Error / functional defect: LED red Operating condition: LED green Supply voltage UB: LED green |
| PIN 1 | A1 Supply voltage UB |
| PIN 2 | X1 Safety input 1 |
| PIN 3 | A2 GND |
| PIN 4 | Y1 Safety output 1 |
| PIN 5 | OUT Diagnostic output |
| PIN 6 | X2 Safety input 2 |
| PIN 7 | Y2 Safety output 2 |
| PIN 8 | IN Solenoid control |
| Recommendation (actuator) | AZ/AZM201-B1 AZ/AZM201-B30 |
| Note (General) | As long as the actuating unit remains inserted in the solenoid interlock, the unlocked safety guard can be relocked. In this case, the safety outputs are re-enabled, so that the safety guard must not be opened. |
品番: 131150435
品番: 151180590
品番: 103040784
品番: 101133843
Hướng dẫn đọc mã van điện từ SMC dòng SY3000, SY5000, SY7000 và SY9000 theo catalog hãng, kèm ví dụ SKU thật và checklist tránh đặt nhầm cấu hình.
Theo đường đi của khí nén để hiểu tiền điện đến từ đâu, tính thử chi phí và chuẩn bị checklist kiểm tra rò rỉ trong nhà máy.
Chọn ống khí PU/PA theo kích thước, áp suất tại nhiệt độ dùng, bán kính uốn và môi trường. Có bảng đối chiếu và checklist thay ống MRO.
