Chưa cập nhật
品番: 131150435
- 単位
- Chưa cập nhật
コンテンツを読み込み中…
コンテンツを読み込み中…
オンライン決済は不要です。TESFA が品番、数量、供給条件を確認し、ご入力の連絡先へ見積を回答します。
MRO 品では、画像だけで選ぶより正しいコード確認が重要です。TESFA は見積確定前に主要な技術項目を確認します。
Khóa liên động điện từ Schmersal 103055346.
品番
103055346
単位
Chưa cập nhật
供給状況
見積はお問い合わせください
必要数量 (Chưa cập nhật)
オンライン決済は不要です。TESFA が品番、数量、供給条件を確認し、ご入力の連絡先へ見積を回答します。
MRO 品では、画像だけで選ぶより正しいコード確認が重要です。TESFA は見積確定前に主要な技術項目を確認します。
| 属性 | 製品仕様 |
|---|---|
| Mã sản phẩm | 103055346 |
| Mã đặt hàng Schmersal | 103055346 |
| Model Schmersal | EX-AZM 161SK-12/12RK-3D |
| Explosion protection: regulations | EN 60079-31 EN IEC 60079-0 |
| Explosion protection zones | 22 |
| Explosion protection category | 3D |
| Explosion protection designation | D II 3D Ex tc IIIC T80°C Dc X |
| Coding level according to EN ISO 14119 | Low |
| Working principle | electromechanical |
| Housing material | Plastic, glass-fibre reinforced thermoplastic, self-extinguishing |
| Gross weight | 1,902 g |
| Power to unlock | Yes |
| Manual release | Yes |
| Number of actuating directions | 3 |
| Number of auxiliary contacts | 2 |
| Number of safety contacts | 4 |
| Performance Level, up to | c | d | e |
| Category | 1 | 3 |
| Note | Electrical life on request. | for 2-channel use and with suitable logic unit. | The tightening sequence of the cover screws must be observed. This can be found in the attached drawing in the “Pictures” tab. | All indications including the conductor ferrules. |
| Please note: | Can be used when fault exclusion for dangerous damage to the 1-channel mechanism is permissible and sufficient protection against manipulation is guaranteed. |
| Note (Performance Level) | Information for the safety classification of the guard locking function is documented in the "Operating instructions" or in the "Operation and mounting" instructions. |
| Actuating play in direction of actuation | 5.5 mm |
| Impact energy, maximum | 7 J |
| Holding force FZh in accordance with EN ISO 14119 | 2,000 N |
| Holding force Fmax, maximum | 2,600 N |
| Latching force | 30 N |
| Positive break travel | 10 mm |
| Positive break force per NC contact, minimum | 10 N |
| Actuating speed, maximum | 1 m/s |
| Mounting | Screws |
| Type of the fixing screws | 3x M6 |
| Type of the screw head | Flat head screw |
| Tightening torque of the fastening screws for the housing cover | 0.6 Nm |
| Tightening torque of the cable gland | 3 Nm |
| Termination | Screw terminals |
| Cable cross-section of the cable glands, minimum | 5 mm |
| Cable cross-section of the cable glands, maximum | 10 mm |
| Cable section, minimum | 1 x 0.75 mm2 |
| Cable section, maximum | 1 x 1.5 mm2 |
| Allowed type of cable | flexible solid multi-wire solid single-wire |
| Length | 40 mm |
| Width | 278 mm |
| Height | 122 mm |
| IP Degree of protection | IP67 |
| Ambient temperature | -10 ... +50 °C |
| Storage and transport temperature | -10 ... +50 °C |
| Note (Relative humidity) | non-condensing non-icing |
| Rated insulation voltage Ui | 250 VAC |
| Rated impulse withstand voltage Uimp | 4 kV |
| Thermal test current | 6 A |
| Rated control voltage | 24 VAC | 24 VDC |
| Required rated short-circuit current | 1,000 A |
| Utilisation category DC-13 | 24 VDC | 2.5 A |
| Electrical power consumption, maximum | 10 W |
| Switching element | NO contact, NC contact |
| Switching principle | slow action, positive break NC contact |
| Maximum switching frequency | 1,000 /h |
| Material of the contacts, electrical | Silver |
| Magnet switch-on time | 100 % |
| Test pulse duration, maximum | 5 ms |
| Test pulse interval, minimum | 50 ms |
| Voltage, Utilisation category DC-13 | 24 VDC | 24 VDC |
| Current, Utilisation category DC-13 | 2.5 A | 2.5 A |
| Note (applications) | hinged safety guard removable guard sliding safety guard |
| Note (Manual release) | For maintenance, installation, etc. For manual release using M5 triangular key, available as accessory |
品番: 131150435
品番: 151180590
品番: 103040784
品番: 101133843
Hướng dẫn đọc mã van điện từ SMC dòng SY3000, SY5000, SY7000 và SY9000 theo catalog hãng, kèm ví dụ SKU thật và checklist tránh đặt nhầm cấu hình.
Theo đường đi của khí nén để hiểu tiền điện đến từ đâu, tính thử chi phí và chuẩn bị checklist kiểm tra rò rỉ trong nhà máy.
Chọn ống khí PU/PA theo kích thước, áp suất tại nhiệt độ dùng, bán kính uốn và môi trường. Có bảng đối chiếu và checklist thay ống MRO.
