Chưa cập nhật
品番: 131150435
- 単位
- Chưa cập nhật
コンテンツを読み込み中…
コンテンツを読み込み中…
オンライン決済は不要です。TESFA が品番、数量、供給条件を確認し、ご入力の連絡先へ見積を回答します。
MRO 品では、画像だけで選ぶより正しいコード確認が重要です。TESFA は見積確定前に主要な技術項目を確認します。
Mô-đun rơ le an toàn Schmersal 101170049.
品番
101170049
単位
Chưa cập nhật
供給状況
見積はお問い合わせください
必要数量 (Chưa cập nhật)
オンライン決済は不要です。TESFA が品番、数量、供給条件を確認し、ご入力の連絡先へ見積を回答します。
MRO 品では、画像だけで選ぶより正しいコード確認が重要です。TESFA は見積確定前に主要な技術項目を確認します。
| 属性 | 製品仕様 |
|---|---|
| Mã sản phẩm | 101170049 |
| Mã đặt hàng Schmersal | 101170049 |
| Model Schmersal | AES 1235 |
| Notice | Discontinued product | for max. 50,000 switching cycles/year and max. 80% contact load |
| Climatic stress | BG-GS-ET-14 EN 60068-2-3 |
| Housing material | Glass-fibre reinforced thermoplastic, ventilated |
| Gross weight | 240 g |
| Wire breakage detection | Yes |
| Cross-circuit detection | Yes |
| Feedback circuit | Yes |
| Automatic reset function | Yes |
| Reset after disconnection of supply voltage | Yes |
| Earth connection detection | Yes |
| Integral system diagnostics, status | Yes |
| Number of LEDs | 1 |
| Number of normally closed (NC) | 2 |
| Number of normally open (NO) | 1 |
| Number of undelayed semi-conductor outputs with signaling function | 2 |
| Number of safety contacts | 2 |
| Number of signalling outputs | 2 |
| Stop-Category | 0 |
| Performance Level, up to | d |
| Category | 3 |
| PFH value | 1.00 x 10−7 /h |
| Safety Integrity Level (SIL), suitable for applications in | 2 |
| Mounting | Snaps onto standard DIN rail to EN 60715 |
| Terminal designations | IEC/EN 60947-1 |
| Cable section, minimum | 0.25 mm2 |
| Cable section, maximum | 2.5 mm2 |
| Tightening torque of Clips | 0.6 Nm |
| Allowed type of cable | flexible solid single-wire |
| Terminal (mechanical) | Screw terminals |
| Width | 22.5 mm |
| Height | 100 mm |
| Depth | 121 mm |
| IP Degree of protection of the enclosure | IP40 |
| IP Degree of protection of the installation space | IP54 |
| IP Degree of protection of clips or terminals | IP20 |
| Ambient temperature | +0 ... +55 °C |
| Storage and transport temperature | -25 ... +70 °C |
| Resistance to vibrations | 10...55 Hz, Amplitude 0.35 mm, ± 15 % |
| Restistance to shock | 30 g / 11 ms |
| Rated impulse withstand voltage Uimp | 4 kV |
| Overvoltage category | III |
| Degree of pollution | 2 |
| Frequency range | 50 Hz 60 Hz |
| Operating voltage | 24 VAC -15 % / +10 %24 VDC -10 % / +20 % |
| Ripple voltage | 10 % |
| Thermal test current | 6 A |
| Rated operating voltage | 24 VAC | 24 VDC |
| Rated AC voltage for controls, 50 Hz, minimum | 20.4 VAC |
| Rated control voltage at AC 50 Hz, maximum | 26.4 VAC |
| Rated AC voltage for controls, 60 Hz, minimum | 20.4 VAC |
| Rated control voltage at AC 60 Hz, maximum | 26.4 VAC |
| Rated AC voltage for controls at DC minimum | 20.4 VDC |
| Rated control voltage at DC, maximum | 28.8 VDC |
| Electrical power consumption | 5 W |
| Contact resistance, maximum | 0.1 Ω |
| Note (Contact resistance) | in new state |
| Drop-out delay in case of power failure, typically | 80 ms |
| Drop-out delay in case of emergency, typically | 20 ms |
| Pull-in delay at automatic start, maximum, typically | 100 ms |
| Pull-in delay at RESET, typically | 20 ms |
| Material of the contacts, electrical | Ag-Ni 10 and 0.2 μm gold-plated |
| Voltage, Utilisation category AC-15 | 230 VAC |
| Current, Utilisation category AC-15 | 6 A |
| Voltage, Utilisation category DC-13 | 24 VDC |
| Current, Utilisation category DC-13 | 6 A |
| Switching capacity, minimum | 10 VDC | 10 mA |
| Switching capacity, maximum | 250 VAC | 8 A | 24 VDC | 2 A |
| Input signal, HIGH Signal "1" | 10 ... 30 VDC |
| Input signal, LOW Signal "0" | 0 ... 2 VDC |
| Conduction resistance, maximum | 40 Ω |
| Voltage, Utilisation category DC-12 | 24 VDC |
| Current, Utilisation category DC-12 | 0.1 A |
| EMC rating | EMC-Directive |
| Note (ISD -Faults) | The following faults are registered by the safety monitoring modules and indicated by ISD. |
| Faults | Cross-wire or short-circuit monitoring of the switch connections Failure of door contacts to open or close Failure of the safety relay to pull-in or drop-out Fault on the input circuits or the relay control circuits of the safety monitoring module Interruption of the switch connections |
| Note (applications) | Guard system Safety sensor |
| Note (General) | Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit. |
品番: 131150435
品番: 151180590
品番: 103040784
品番: 101133843
Hướng dẫn đọc mã van điện từ SMC dòng SY3000, SY5000, SY7000 và SY9000 theo catalog hãng, kèm ví dụ SKU thật và checklist tránh đặt nhầm cấu hình.
Theo đường đi của khí nén để hiểu tiền điện đến từ đâu, tính thử chi phí và chuẩn bị checklist kiểm tra rò rỉ trong nhà máy.
Chọn ống khí PU/PA theo kích thước, áp suất tại nhiệt độ dùng, bán kính uốn và môi trường. Có bảng đối chiếu và checklist thay ống MRO.
